The TT [a] is an out-of-production Soviet semi-automatic pistol. It was developed in the early s by Fedor Tokarev as a service pistol for the Soviet military to replace the Nagant M revolver that had been in use since Tsarist times , though it ended up being used in conjunction with rather than replacing the M It served until , when it was replaced by the Makarov pistol. In , the Revolutionary Military Council approved a resolution to test new small arms to replace its aging Nagant M revolvers. A few weeks later, 1, TTs were ordered for troop trials, and the pistol was adopted for service in the Red Army. But even as the TT was being put into production, design changes were made to simplify manufacturing.

Author:Kiganos Vujar
Country:Saint Lucia
Language:English (Spanish)
Published (Last):17 October 2011
PDF File Size:1.11 Mb
ePub File Size:17.72 Mb
Price:Free* [*Free Regsitration Required]

Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all of the chapters. The effective shooting range is approximately 75 feet. BBs fired from this Airsoft gun may travel further than intended. Make certain that you have an adequate backstop. Eye protection should be worn at all times when both shooting and maintaining your Airsoft gun.

Protect your eyes from BBs under pressure while performing maintenance on your Airsoft gun. Until you are certain the chamber is empty, treat every gun as if it were loaded. Always remove the magazine and visually check to confirm the chamber is empty. Ensure the Airsoft gun barrel is free of obstructions before you fire the gun. Even the smallest obstruction such as lubrication or a stuck cleaning patch can cause a misfire or malfunction. Always keep the muzzle of the gun pointed in a safe direction.

Never point the muzzle at a person or object that you do not intend to shoot. Keep your finger off the trigger and out of the trigger guard until your sights are aligned on your target and you are ready to fire.

Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces where BBs are likely to ricochet in unpredictable directions. If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel. BBs can become lodged into the chamber, and serious eye injury may occur. Performing proper maintenance, as outlined in this manual, ensures that your Airsoft gun will be safe to shoot and will perform to its designed specifications for many years.

Alterations, modifications or adjustments may damage your Airsoft gun, make it unsafe to shoot, and will void all warranty claims. Always store the Airsoft gun in a safe place, and out of the reach of children. Always transport the Airsoft gun in a carrying case. Never display the Airsoft gun in a public place. Keep the safety engaged, and remove the magazine before storing the Airsoft gun. Note: it is your responsibility to take every reasonable precaution to ensure the safe storage and transportation of your Airsoft gun.

The orange tip on Airsoft guns helps Law Enforcement distinguish between the replica guns from their real firearm counterparts. Altering the coloration or markings required by state or Federal law so as to make the product look more like a firearm is dangerous and may be a crime. Operator assumes all risks and responsibility when doing so. Airsoft guns have been mistaken by Police and Law Enforcement as real firearms.

A confrontation with law enforcement while carrying an Airsoft gun can result in serious injury or even death.

It is strongly advised to operate the Airsoft gun at a safe and legal location. In the event that you are approached by Law Enforcement personnel, you must comply with their instructions immediately to avoid an incident.

Do not handle or operate your Airsoft gun while under the influence of alcohol, medication or drugs. Your Airsoft gun is well-engineered and manufactured to the highest standards. It was carefully inspected before it was packaged and shipped from our factory. Its safe use depends on you alone. You are the ultimate safety device.

Like many other devices, your Airsoft gun is safe unless handled in an irresponsible or uneducated manner. Release the magazine by pressing the magazine catch button. Push the gas canister nozzle into the charging valve.

Make sure both the canister and magazine are inverted and in the vertical position when charging. Charge the magazine until gas overflows from the charging valve. Sudden impact with a hard surface may cause damage to the magazine. It is recommended to keep the gas release valve slightly oiled. Room temperature is the ideal temperature for shooting. It is strongly recommended to empty the gas from the magazine after shooting.

Be certain that the gas does not make contact with eyes or skin while being released, as any contact will cause cold burns. Pull the magazine follower down until it locks. Insert BBs into the magazine lip.

Make sure to have a 3mm clearance between BBs and the top lip of the magazine. Push the magazine follower lock to release. For best result use 0. Never use recycled or low grade BBs to prevent damage to your gun. Doing so will damage the magazine and magazine follower. Place the magazine back into the magazine well. Push the magazine up until it clicks into a locked position. Pull the magazine down to assure that it has been locked in place.

This will automatically load the BBs into the chamber. The hammer will be in a cocked position. Make sure not to skip this procedure. Skipping this step will cause a misfire on the first pull of the trigger. The slide will stay open when the last BB is fired and ejected. Make sure the gun is cocked.

Grasp the Airsoft gun in your hand firmly. A two-hand hold with one hand wrapped around the other will help control the Airsoft gun. Squeeze the trigger, the blow back action will load the following BBs automatically as the slide cycles back and forth. Doing so may damage the impact block and result in the loss of the impact pin.

Remove the empty magazine and replace it with a loaded magazine, then release the slide stop. The first BB will be automatically loaded into the chamber. Make sure both the magazine and the chamber are clear without BBs. Airsoft BBs are light-weight and can be affected by wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted according to the shooting environment or surroundings.

Remove the magazine. Open the slide and place adjusting tool into the slotted chamber ring. If the BBs are dropping too quickly, move the adjusting ring to the left or counter-clockwise to give the BB more hop.

If the BBs are dropping too slowly, move the adjusting ring to the right or clock-wise. Test fire and adjust as needed. Remove the magazine by depressing the magazine catch button.

Check and clear the chamber of BBs. Push the slide stop retainer toward the rear to release the slide-stop release pin. Remove the slide stop by pushing on the right side of the frame. Pull off the slide-stop from the left side of the frame. Glide the slide forward, away from the frame. Slide the barrel unit out from the slide. Place the barrel unit into the slide and re-attach the barrel bushing to the barrel tip. Install the recoil spring and guide rod into position. Make sure the hammer reset lever is pushed down.

Put the assembled slide onto the frame rails and glide it toward the rear of the gun. Re-attach the slide stop release to the slide and push the slide stop retainer back into position. Push the slide toward the rear, cycle the slide back and forth to ensure proper assembly. With lubricating silicone oil, it will extend the life of the seals and o-rings and prevent gas leaks.

Any other type of lubricant may damage the products. Lightly lubricate the recoil spring, cylinder and moving parts with a few drops of oil. Lubricating the seals and o-rings are essential. Unload BBs from the magazine. Operating Under Unusual Conditions Unusual conditions are defined as any condition requiring special maintenance. Perform maintenance outlined for the climate similar to your operational area.

Operating an Airsoft gas gun in extremely cold temperatures is not recommended. Cold temperatures will cause the Hop-up Bucking to harden, reducing its effectiveness.


Polish Instruction Manuals – TT33, Mosin-Nagant, PPS-43

Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all of the chapters. The effective shooting range is approximately 75 feet. BBs fired from this Airsoft gun may travel further than intended. Make certain that you have an adequate backstop. Eye protection should be worn at all times when both shooting and maintaining your Airsoft gun.


Tokarev Pistol Manual by D. R. Morse






Related Articles