Quick Links. See also: Technical Information , Instruction Manual. Table of Contents. Makita ; ; ; ; ; mlt table saw stand 20 pages. Page 2: Specifications The tool is intended for cutting in wood.
|Published (Last):||27 December 2015|
|PDF File Size:||15.74 Mb|
|ePub File Size:||7.57 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. See also: Technical Information , Instruction Manual. Table of Contents. Makita ; ; ; ; ; mlt table saw stand 20 pages. Page 2: Specifications The tool is intended for cutting in wood. Read all these instructions before operating this product and save these instructions. For safe operations: tion and changing accessories. Make sure the blade is not contacting the riving Wear eye protection. Page 5 Never yank cord to discon- work.
To reduce your exposure to these nect from receptacle. Keep cord away from heat, chemicals: work in a well ventilated area oil, water and sharp edges.
It should be installed in an area that leaves enough room to easily handle the size of your workpieces. The table saw should be secured mm with four screws or bolts to the work bench or table saw stand using the holes provided in the bottom of the table saw.
Page 7: Functional Description Storing accessories The miter gauge, blade and wrenches can be stored on the left side of the base and the rip fence can be stored at the right side of the base. The blade guard to be removed in dado cutting can be stored at the right hand rear. To check and adjust the positive stops, proceed as follows: Move the handwheel as far as possible by turning it.
Page 9 The hinged switch lever plate can be locked by passing padlock through the hasp on the left hand side. To start the tool, press the ON I button. Page 10 Always be sure that the tool is switched off and unplugged before installing or removing the blade. Failure to do so may result in overtightening or insufficient tightening of the hex bolt.
This could cause an injury. Page 11 For Model Max. Blade thickness Kerf mm mm 1. Always use the correct ring for the arbor hole of the blade you intend to use. For non- European type blade guard Remove the center cover. Insert the riving knife into the blade guard mounting portion stay. Tighten the hex bolts A with the provided wrench. Page 13 For both European and non-European type blade guards The riving knife installing location is factory-adjusted so that the blade and riv- ing knife will be in a straight line.
However, if they are not in a straight line, loosen the hex bolts B and adjust the blade guard mounting portion stay so that the riving knife is aligned directly behind the blade. Page 14 To check to be sure that the rip fence is parallel with the blade, secure the rip fence 2 - 3 mm from the blade. Raise the blade up to maximum elevation. Mark one of the blade teeth with a crayon. Measure the distance A and B between the rip fence and blade. Page 15 0 graduation, loosen the screw on the scale plate and adjust the scale plate.
Guideline 2. Screws Connecting to vacuum cleaner Cleaner operations can be performed by connecting the tool to Makita vacuum cleaner or dust collector. Page 17 Auxiliary fence Make auxiliary fence from 9.
Wood facing for the rip fence should be the same size as the rip fence. Page 18 When the width of rip is 65 mm - mm wide, use the push stick to feed the workpiece. Push stick When the width of rip is narrower than 65 mm, the push stick can- not be used because the push stick will strike the blade guard. Use the auxiliary fence and push block.
Page 19 Miter gauge Use the miter gauge for the 4 types of cutting shown in the figure. Brush holder cap The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. Page 22 Memo Page 23 Memo Print page 1 Print document 24 pages.
Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Makita 2704 Instruction Manual
Our goal is to provide you with a quick access to the content of the user manual for Makita Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Makita If looking through the Makita user manual directly on this website is not convenient for you, there are two possible solutions:. Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Makita but the selected pages only. Below you will find previews of the content of the user manuals presented on the following pages to Makita
Makita 2704 Table Saw Parts
Quick Links. Table of Contents. Makita ; ; ; ; ; mlt table saw stand 20 pages. Page 2: Specifications EC Declaration of Conformity Do not dispose of electric equipment Makita Corporation responsible together with household waste material! Page 3 Tomoyasu Kato Never carry the tool by the cord or yank it to Director disconnect it from the socket.
- FLAMMABLE.GASES AND LIQUIDS AND THEIR HAZARDS.EPA 744-R-94-002 PDF
- JULIUS PANERO ERGONOMIA PDF
- ANTHONY WESTON A RULEBOOK FOR ARGUMENTS 4TH EDITION PDF
- HML 5000 SONNEBORN PDF
- HVDC KR PADIYAR PDF
- DEFENDU BY W.E.FAIRBAIRN PDF
- CHRIS COLFER THE WISHING SPELL PDF
- KOLKATA KNIGHT RIDERS BALANCE SHEET FILETYPE PDF