No category. If the mounting clamps are on the unit, put out them before inserting the unit to the panel. Pt Pt Max. Weight: ESM : gr. ESM : gr.
|Published (Last):||28 May 2019|
|PDF File Size:||16.62 Mb|
|ePub File Size:||16.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Megal Do not do the montage of ems device with inappropriate fixing clamps. It determines operation form of hysteresis. Deviation range alarm Heater failure alarm. Operator can see operator menus and parameters but operator can not change the parameters. Tampering with the unit may results in malfunction, electric shock or fire.
Display adjustment low point value is fixed todisplay adjustment high point value is fixed to If analogue input value is em than minimum value of operating scale top display starts to blink. During the equipment is putted in hole on the metal panel while mechanical installation some metal burrs can cause injury on hands, you must be careful. When tune operation finishes if this parameter is 0, it can not es, changed because derivative control part does not perform. It determines logic output function of Output Press menu button to exit without saving Set value.
Even if this parameter is 0, this parameter is accepted 50 msecs for security. It is visible if one of analogue input modules is plugged in Module-1 or Module-2 socket If process value is less than minimum value of operating scale or for analogue input module in Module-1 or Module-2 socket or greater than maximum value of operating scale or for analogue input module in Module-1 or Module-2 socket, process output becomes active. When tune operation finishes, it can be changed by the device.
It is active ifV CT input module is plugged in Module-2 socket. It can be adjusted from 0. Never attempt to disassemble, modify or repair this unit. This parameter is visible if one of the analogue input modules is plugged in Module-2 socket Alarm on delay time 0, Ezm It is active if logic output function of Module-1 is an alarm output Alarm off delay time 0, Seconds Alarm off delay time. For starting normal operation power off and pull out one of the analogue input modules.
If this parameter 0. Po04 Po03 If process value is less than minimum of operating scale for analogue input module in Module-2 socket or greater than maximum value of operating scale for analogue input module in Module-2 socket, process output becomes active. The unit is normally supplied without a power switch or a fuse.
Even as a result of the cooling PID calculation device calculates the output value less than this parameter, cooling output is active minimumor OLLC parameter. It means alarm latching output is selected. In normal operation, it controls the tune conditions in Auto Tune selection which explained below.
This must be selected, if analogue input module in Module-1 socket is EMI Use of these solvents can reduce the mechanical reliability of the device. It is your responsibility if this equipment is used in a manner not specified in this instruction manual. It turns to operation screen without accessing to parameters. This warranty is provided for a period of two years. In multi point display adjustment operation, defined scale is divided into 16 adjustment points.
Selectable dual point calibration is performed. Kazrajinn Be sure to use the rated power supply voltage to protect the unit against damage and to prevent failure. It can be changed according to analogue input type and scale. Value between 5 and seconds can be entered. This parameter is visible if Logic output function of Output-3 is Alarm output and one of the analogue input modules is plugged in Module-1 or Module-2 socket Minimum value of operating scale Low Limit.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information. Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies.
Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary Always Enabled. Non-necessary Non-necessary.
ESM 4950 PDF
Accelerating the renovation of the Bulgarian building stock. Strengthening energy security in South-East Europe by investing in buildings. Vitaminka Macedonia invests in new infrastructure and product line. Hemofarm invests millions euro in its Serbian division. S is implemented in a plant of Valeo in Turkey.
Siampower Technology Co.,Ltd.