The DriveRack products provide the tools that ensure that the system sounds its very best. The capitalizes on the road tested and contractor approved nature of the other products in the DriveRack line. The provides full bandpass and crossover configurations as well as independent output processing and a full time RTA for live sound applications. The DriveRack continues the legacy of DriveRack series, which has been created by the company that has been redefining the standard of signal processing for more than 30 years. The DriveRack was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface.
|Published (Last):||22 January 2012|
|PDF File Size:||14.20 Mb|
|ePub File Size:||4.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. See also: Manual. Table of Contents. Page 3 , usA date: may 19, european contact: Your local dbx sales and service office or If you want to dispose this product, do not mix it with general household waste.
There is a separate collection system for used electronic products in accordance with legislation that harman music Group requires proper treatment, recovery and recycling.
The DriveRack essentially becomes the only device that you will need between the mixer and the power amps. Page 7: Service Contact Info After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the factory service facility. In all cases, you are responsible for transportation charges to the factory. Page 8: Warranty In no event shall dbx or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
Note: dbx Professional Products recommends that power amplifiers connected to the DriveRack , should be powered down prior to cycling the power on the DriveRack FX buttons - This array of 12 FX buttons is your primary mode of directly accessing any effect module. From program mode, press the EQ button to reach the EQ module to be edited. Successive presses of the EQ button will move through each channel. Successive presses of the Other button will move you to each of the various insert modules available.
Pressing the Data Wheel will select the effect parameter to be edited. Page Navigating The Delay Section the pages of selected module.
Successive presses of the Data wheel will select effect parameters within the currently selected page. Navigating the Delay Section 2.
The following information provides, descriptions about program functions and in depth configuration options of the DriveRack To instantly access an effect module, simply press the corresponding button in the button array for the desired module.
For some configurations, you may be able to simply select one of these presets as a starting point and edit the program from there. In the Quick Start section of this manual, you saw how you can use the Wizards to configure basic programs i. The upper left-hand corner of the display Program 1 indicates what EQ type is currently selected. The A and B indicators indicate which input is currently selected. The upper left-hand corner of the display indicates what Crossover type is currently selected.
The following section will provide you with descriptions and explanations of all parameters within the DriveRack Level 9 to 12 dB Sets the overall gain of the high shelf parametric 4. FIXED mode is used before the performance without any input signal. In LIVE mode, the live filters automatically detect and remove feedback during the performance. When all of the live filters have been used, they begin to round robin.
Essentially this means that the first filter set is replaced where a new feedback is detected and notched out. This is done by selecting a desired Target output level and Window. Up to six Notch filters are available for all six outputs.
Types include: Bell - All bands are bell-shaped. This lets you choose the exact knee that is needed for the dynamic effect you are looking for. Input 2 Level -Inf to 20dB Adjusts the input level of input 2. Master level -Inf to 20dB This parameter is used to control the overall level of the mixed input signals. Additionally, pressing and holding the Utility button will allow you to enter the metering section of the Page Zc Setup Output 5.
This feature gives you the ability to control various parameters of the such as Output Levels, Mute and Program Changes. Up to six ZC panels can be connected to a DriveRack Pressing the DATA wheel again and rotating it then allows you to assign this binary switch combination to a program to be loaded.
The cable must be wired like this: DB-9 female-to-female null modem cable Important Note! A straight through RS cable will not work with the DriveRack. ZC-1 The ZC-1 is a programmable zone controller that allows output volume level control from a wall panel. To wire in series each Zone Controller must have an identification or zone number chosen using the DIP switches on the side of the controller see diagram A.
An example of this is shown in Diagram C. Connect the outputs from the mixer to the inputs of the DriveRack. Connect the outputs of the DriveRack and run to the selected speaker amplifier. Making sure that all outputs are muted, apply power to the mixer and amplifiers.
Software 1. Adjust the individual parameters for the system by pressing the Processing Module buttons. The Soft Reset resets all operating parameters except user programs. The Hard Reset Procedure will reset all programmable information back to the factory defaults. Page Specifications Alignment Delay: Total of 2.
The Auto-EQ can be used to adjust your system to compensate for room effects, and adjust the response of the entire system to your liking. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Gain structure refers to aligning the gain of each device so that they all clip at the same point, and the noise floor of the entire system is at its absolute minimum. E-mail us at: customer dbxpro. Print page 1 Print document 84 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password.
Upload from disk. Upload from URL.
Quick Links. See also: Manual. Table of Contents. Page 3 , usA date: may 19, european contact: Your local dbx sales and service office or If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that harman music Group requires proper treatment, recovery and recycling. The DriveRack essentially becomes the only device that you will need between the mixer and the power amps.
dbx DriveRack 260 User Manual – Download
dbx DriveRack 260 User Manual
- BARBARA SZACKA WPROWADZENIE DO SOCJOLOGII PDF
- ANTONY BEEVOR THE SPANISH CIVIL WAR PDF
- MAESTROS DE LA LUZ DENNIS SCHAEFER PDF
- DIXELL XC650C PDF
- ALICE BAILEY TRATADO SOBRE MAGIA BLANCA PDF
- ENCIKLOPEDIJA NOVIH RELIGIJA PDF
- CRIPPLE CREEK BANJO TAB PDF
- EVANGELIO APOCRIFOS PDF
- THE COMPLETE TRADING COURSE COREY ROSENBLOOM PDF