Download 7 pages , 2. The definitions below describe the le vel of se verity f or each signal word. Please read the. Double insulated tools are constructed throughout with two separate la yers of electrical.

Author:Doutaxe Akinobei
Language:English (Spanish)
Published (Last):11 May 2012
PDF File Size:7.53 Mb
ePub File Size:7.82 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. See also: Instruction Manual. The definitions below describe the level of severity for each signal word. Please read the. Tools built with this insulation system are not intended to be grounded. As a result, your tool is. NOTE: Double insulation does not take the place of normal safety precautions when operating.

The insulation system is for added protection against injury resulting from a possible. Polarized plugs one blade is wider than the other are used on equipment to reduce the risk of.

When provided, this plug will fit in the polarized outlet only one way. If the plug. If it still does not fit, contact a qualified electrician. Do not change the plug in any way. Form habit of checking to see that keys. Tools, scrap pieces,. Cluttered areas and benches invite accidents. Keep your work area. All visitors should be kept at a safe distance from work area. The unauthorized start-up of a machine by a child or visitor may result in injury. It will do the job better and be safer at the rate for which it was.

Don't force tool or attachment to do a job for which it was not designed. Using the incorrect tool or attachment may result in personal injury. No loose clothing, gloves, neckties, rings, bracelets, or other. Non-slip footwear is recommended. Air vents may cover moving parts and should also be. Everyday eyeglasses are NOT safety glasses. Use clamps or a vise to hold the workpiece on the table. It is safer than using your hand and it frees both hands to operate tooL. Keep proper footing and balance at all times.

Loss of balance may. Keep tools sharp and clean for best and safest performance. Poorly maintained. An accidental start-up can cause injury. Do not. Make sure that the switch is in the. Make sure your extension cord is in good condition, ff. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate. The smaller the gauge number, the.

Before further use of the tool, a guard or other part that is. A guard or other. Do not use tool if switch does. The use of improper accessories may cause risk of injury to persons. Serious injury could occur if the tool is tipped or if the cutting tool. Don't leave tool until. Serious injury can result. Motors in these tools may spark and ignite fumes.

DO NOT. A moment of inattention while operating power tools may result in injury. Do not allow familiarity gained from frequent use of your saw to replace safety. Always remember that a careless fraction of a second is sufficient to inflict severe injury. A machine incorrectly assembled can cause serious injury.

Knowledge is safety. Make sure the miter saw is placed on a secure supporting surface and does not. Protect electric supply line with at least a 15 ampere time-delay fuse or a. The teeth on the blade should. Loose clamps can. Loose or improper blade clamping may result in. Check the blade to see if it runs true and is free from. Overheating, damage to the tool and personal injury may occur. Damage to tool. DO NOT force cutting action. Stalling or partial stalling of motor can cause damage.

To the. Starting the cut too. The excessive heat and abrasive particles generated. NEVER have any part of your body in line with the path of the saw blade. Personal injury will. NEVER apply blade lubricant to a running blade.

Applying lubricant could cause your hand to. DO NOTplace either hand in the blade area when the saw is connected to the power source. Inadvertent blade activation may result in serious injury. Hold the work firmly against the fence and table. Free-hand operations on a miter saw. A blade can cause serious injury. DO NOT reach underneath the saw unless it is unplugged and turned off. Contact with saw. Do not use blades. These can deflect and contact the guard, and can cause damage to the.

A cracked or damaged. Replace cracked or damaged blades immediately. Cleaning the blade and. A cracked. Table of Contents. One DW Page 6: Vernier Scale DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time The advantage to cutting crown molding using this method is that no bevel cut is required.

Print page 1 Print document 7 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.


Dewalt DW716 TYPE3 User Manual MITER SAW Manuals And Guides 1301211L



DeWalt DW716 Instruction Manual



DeWalt DW716 TYPE3 miter saw manual


Related Articles