ASTM D434 PDF

Close menu. Amerikanische norm astm d fuer die rutschfestigkeitspruefung der garne in den gewebenaehten. Rutschfestigkeit der kettfaeden im zusammenhang mit dem schuss. Pruefung der moebelstoffe.

Author:Fautilar Gok
Country:Morocco
Language:English (Spanish)
Genre:Spiritual
Published (Last):4 March 2011
Pages:328
PDF File Size:12.26 Mb
ePub File Size:2.22 Mb
ISBN:730-8-43099-594-4
Downloads:27893
Price:Free* [*Free Regsitration Required]
Uploader:Faunos



ASTM D this standard has been replaced, but still used habitually by many foreign buyers. JIS l section 8. Sampling: due to the diversity of fabrics, sampling should be representative. For example, jacquard fabrics should be processed according to the jacquard situation, whether the seam slip test of jacquard part and ground tissue part should be tested or not.

For pigment printing weave, need to consider whether to avoid printing parts. Sample making: in the process of sample making, it is necessary to make samples strictly according to the sample making methods and requirements stipulated by the content of each standard.

Equipment regulation: due to the difference of Seam slip tester produced by different equipment manufacturers at home and abroad, please carefully understand the equipment state effective clamping area of clamping piece, clamping pressure of pneumatic fixture, sensitivity when the equipment stops drawing and parameter setting effective clamping distance and stretching rate before the test.

Whether the data collection mode and frequency of the equipment software meet the standard requirements. Testing: during testing, testers are required to observe the sample testing process;To understand the abnormal phenomenon of samples in the test process;Instead of staring at a computer screen and stretching the curve. Result analysis: not all test results are reasonable;We need to reject the test sample data with abnormal conditions and understand the fracture situation of each sample during the test, so as to analyze whether the test results meet the standard requirements.

Material preparation. The commonly used sewing needles for seam slippage of fabrics used in clothing are divided into no. Different size and diameter of the needle will affect the size of the hole left in the fabric. This has a great influence on the constant load test, so we must pay attention to it. The sharpness of the sewing needle will also affect the sewing damage rate of the fabric, thus affecting the maximum peak value of the fabric's seam strength, which is the main content of the seam slip.

Test direction problem. The testing direction is generally divided into two types. The two are opposite, so when we get the test report, we must see which direction the yarn slip is bad. This is also sometimes difficult for customers to understand a problem. In order to be clear to the customers, each testing center has adopted the following result representation method.

It means that the suture is parallel to the meridian, and the suture is parallel to the latitudinal direction.

Notes for sample preparation. Except that JIS L requires the sewing thread to be perpendicular to the warp latitude , all other standards require the sewing thread to be parallel to the short side of the sample.

In addition to JIS L, other standards require drawing a straight line parallel to the long side at a distance of 38mm from the long side, so that the fixture can hold the same bundle of yarn during the test. When sewing samples, be sure to check whether the tension between the upper and lower threads of the sewing machine is consistent. The diagram below:. If the sewing tension of the upper and lower thread is consistent, the sewn sample shall be evenly distributed on both sides.

During the test, the tension of the yarn is uniform and can fully reflect the true stress of the sample. As shown in the figure above, the tension of the upper and lower sewing thread is inconsistent.

In this case, the tension strength of the sewing thread is relatively weak, and the test result is unstable. After several tests, it is found that the test result is slightly lower than the normal test value, and it is easy for the seam to break. Or adjust the second screw on the bottom line coil to use less tension. Email: hello utstesters. Web: www. What We Do? Why Choose Us?

Contact Us. Blog Catalog Products News Industry News Blog Latest Blog The formation cause of pilling and its detection method What are the factors that influence the breathability and moisture permeability of composite fabric? ISO - Material preparation Sewing needles: The commonly used sewing needles for seam slippage of fabrics used in clothing are divided into no. Test direction problem The testing direction is generally divided into two types 1.

Notes for sample preparation 1. The diagram below: If the sewing tension of the upper and lower thread is consistent, the sewn sample shall be evenly distributed on both sides.

Previous Next. Quick Links. Sitemap Blog XML.

DP83848CVV PDF

Popular Publishers

Learn more about Scribd Membership Home. Much more than documents. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Start Free Trial Cancel anytime. Uploaded by jaguni.

LEARN TEELINE SHORTHAND PDF

Search Results For: " ASTM D434 "

.

EPAP MODELLO 2 2012 PDF

.

Related Articles